Search found 6707 matches
- Fri May 17, 2024 6:20 pm
- Forum: Wanted
- Topic: Emblem / Badge Source
- Replies: 1
- Views: 36
Re: Emblem / Badge Source
Melvins is a good place to get comet parts. well known on here. not a big major corporation . good people. His name is Randy Milner. & they now have new 64-65 console bodies & other console parts.
- Fri May 17, 2024 12:29 am
- Forum: 60 - 63 Comets
- Topic: Ol' Black Mattie 63' Comet Custom Build
- Replies: 9
- Views: 514
Re: Ol' Black Mattie 63' Comet Custom Build
It's going to be a fun little car!
- Thu May 16, 2024 4:08 pm
- Forum: Comet Forum Events
- Topic: Comet Gathering 2024
- Replies: 4
- Views: 656
Re: Comet Gathering 2024
I've seen several on facebook going so y'all wont be lonely
- Wed May 15, 2024 8:46 pm
- Forum: 60 - 63 Comets
- Topic: Removing rear wheels on 63’
- Replies: 5
- Views: 50
Re: Removing rear wheels on 63’
Yea you can jack up that far forward, motor is plenty of counter balance, or even without a motor . After I installed my monoleafs which were a lot stiffer I still couldn't get these wide tires on with suspension dropped so I made up a deal with what I could find on hand ,all-thread, channel metal s...
- Thu May 09, 2024 8:19 pm
- Forum: 64 - 65 Comets
- Topic: Lou's 65 Comet Build
- Replies: 957
- Views: 183815
Re: Lou's 65 Comet Build
Yea once you think of heat shrink as a universal covering it opens up many uses. Started with the lanyards, but have found a few other uses for it on my build! Lou I'm surprised you didn't cover the whole lanyard,,,or at least up past the part that looks to be rubbing on the hood trim. :? btw, did ...
- Tue May 07, 2024 7:09 pm
- Forum: 64 - 65 Comets
- Topic: Lou's 65 Comet Build
- Replies: 957
- Views: 183815
Re: Lou's 65 Comet Build
I so very much needed to see this.especially that last pic! :D my flange was wavy & not put together right in places with one side of flange higher than the other. I had been trimming it & getting the waves out a while back. Now I know how I will check it all . So Thanks again. been in the back of m...
- Tue May 07, 2024 1:38 pm
- Forum: Comet Lounge
- Topic: Zinc info
- Replies: 8
- Views: 183
Re: Zinc info
Fred basically he said too much of a good thing is not good. Use the proper amount for break in and be done with it.
- Mon May 06, 2024 6:06 pm
- Forum: Comet Lounge
- Topic: Zinc info
- Replies: 8
- Views: 183
Zinc info
If you have 20 spare minutes this is kinda interesting;
https://www.youtube.com/watch?v=erxjPicpYyw
https://www.youtube.com/watch?v=erxjPicpYyw
- Mon May 06, 2024 12:04 pm
- Forum: 64 - 65 Comets
- Topic: Seat Track Nightmare
- Replies: 4
- Views: 231
Re: Seat Track Nightmare
fuzzydriver after looking at the picture/exploded view of seat & parts that you found & posted from Kevins post again I noticed at the top of the page is an enlargement of the attachment of the wire to front of the seat .instead of hogrings it looks like hooks,,,,which make more sense > would be eas...
- Sat May 04, 2024 4:40 pm
- Forum: 64 - 65 Comets
- Topic: Seat Track Nightmare
- Replies: 4
- Views: 231
Re: Seat Track Nightmare
Here are some pics of the seat out of my car with wire that is run thru 2 or 3 rings on the frame. if you zoom in on second pic you can see that it would be above the hog rings that are holding the cover on which helps it get over the hump https://i.postimg.cc/DZQ9BKP9/SDC11133.jpg https://i.postimg...
- Sat May 04, 2024 2:36 pm
- Forum: 64 - 65 Comets
- Topic: Seat Track Nightmare
- Replies: 4
- Views: 231
Re: Seat Track Nightmare
If what you are calling a tie rod is the wire that goes from one side track lock to the other side one with a turn buckle to adjust it. It should be ran through a hog ring at front of seat in the center of the seat. This takes up the slack while keeping it from dragging on the drive shaft tunnel. I ...
- Sat May 04, 2024 2:24 am
- Forum: 64 - 65 Comets
- Topic: Root's 64 Cyclone Build
- Replies: 280
- Views: 10927
Re: Root's 64 Cyclone Build
That's impressive!
- Fri May 03, 2024 9:25 pm
- Forum: Showing Off
- Topic: Let me start!!!!!!!!
- Replies: 664
- Views: 233816
Re: Let me start!!!!!!!!
Looks great Fred! with same od It may not be lower but the taller rim is closer to fender at top giving the eye a lower perspective .
- Wed May 01, 2024 11:49 am
- Forum: Comet Lounge
- Topic: WOW the birthdays!!!!
- Replies: 627
- Views: 125002
Re: WOW the birthdays!!!!
Happy Birthday Boss !
- Mon Apr 29, 2024 6:36 pm
- Forum: 60 - 63 Comets
- Topic: 63 single master bowl upgrade to dual
- Replies: 7
- Views: 274
Re: 63 single master bowl upgrade to dual
Going to a dual master is OK, but if you don't replace all the wheel cylinders as well. why bother with the master. I would say for the safety of the dual MC. because if you rupture a line with a single MC you wont have any brakes at all. but if you rupture a line with a dual MC it can only affect ...