Dual Quad

65 hipo · Post by **65 hipo** » Mon Apr 13, 2015 5:05 pm

This has been a long time coming. I have wanted to put a dual quad intake on my car since I bought it. I still have a few things to come up with like the throttle linkage and a fuel line from the fuel pump to fuel log.

This is how it looked when I started

Post by **poboyjo65** » Mon Apr 13, 2015 5:24 pm

Looks badass!

CALIFORNIA CALIENTE · Post by **CALIFORNIA CALIENTE** » Mon Apr 13, 2015 5:45 pm

KOOL!!

popscomet · Post by **popscomet** » Mon Apr 13, 2015 6:16 pm

Looks good,what CFM are those carburaters ??...POP

65clevorcyclone · Post by **65clevorcyclone** » Tue Apr 14, 2015 12:10 am

Where did you get those pent roof valve covers?

65 hipo · Post by **65 hipo** » Tue Apr 14, 2015 12:59 pm

The carburetors are Holley’s 450 cfm (Holley#510-0-9776). And the valve covers are Ford Racing valve covers (M-6582-W427B). I milled the 427 Cobra out and water jetted the inserts. Thanks guys Ryan Vassel

Post by **poboyjo65** » Tue Apr 14, 2015 5:30 pm

I knew I'd never seen v covers like those.

You may need to make a new set of inserts with a revised horsepower increase with the extra carb!

it all looks great,very clean!

popscomet · Post by **popscomet** » Tue Apr 14, 2015 5:55 pm

65 hipo wrote:The carburetors are Holley’s 450 cfm (Holley#510-0-9776). And the valve covers are Ford Racing valve covers (M-6582-W427B). I milled the 427 Cobra out and water jetted the inserts. Thanks guys Ryan Vassel

I've had 2 500 edelbrocks on my COMET since back in the 90's,,they work great....my son turned out on a lathe my alumn fuel block and my linkage was made from 2 tenshion rods on the windshield wipers from a LOCOMOTIVE,and both my carbs are together,no progressive linkage,,and it amaze's me how this 289 will get down to such low rpm's in 4thgear and just put along and just lay into the throttle slowly and it picks up and just goes,don't miss buck or act up.....at the time I put 2 4's on mine ,all I had was a EDELBROCK intake,,so thats what I used ,,but now I have a intake that hollys will bolt on........yours looks very nice.......POP

ec164 · Post by **ec164** » Tue Apr 14, 2015 7:08 pm

Nice engine compartment. Great job on valve covers. Have fun with dbl.trouble

no tickets..............Al

albert · Post by **albert** » Tue Apr 14, 2015 8:30 pm

Your engine compartment looks soooooo nice! Good luck with the new set up.

popscomet · Post by **popscomet** » Tue Apr 14, 2015 8:50 pm

BODY color under the hood is the only way to go.......JMO.....that's the only thing I liked about an old Mopar.......pop

barrys65cyclone · Post by **barrys65cyclone** » Wed Apr 15, 2015 12:51 am

I have a Holman Moody Dual Quad set up ready to install on my 289 after I get back from Ocean City car show.

COMET CENTRAL

Dual Quad

Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad

Re: Dual Quad