Search found 6707 matches

by poboyjo65
Fri May 17, 2024 6:20 pm
Forum: Wanted
Topic: Emblem / Badge Source
Replies: 1
Views: 35

Re: Emblem / Badge Source

Melvins is a good place to get comet parts. well known on here. not a big major corporation . good people. His name is Randy Milner. & they now have new 64-65 console bodies & other console parts.
by poboyjo65
Fri May 17, 2024 12:29 am
Forum: 60 - 63 Comets
Topic: Ol' Black Mattie 63' Comet Custom Build
Replies: 9
Views: 514

Re: Ol' Black Mattie 63' Comet Custom Build

It's going to be a fun little car! :D
by poboyjo65
Thu May 16, 2024 4:08 pm
Forum: Comet Forum Events
Topic: Comet Gathering 2024
Replies: 4
Views: 652

Re: Comet Gathering 2024

I've seen several on facebook going so y'all wont be lonely :D
by poboyjo65
Wed May 15, 2024 8:46 pm
Forum: 60 - 63 Comets
Topic: Removing rear wheels on 63’
Replies: 5
Views: 50

Re: Removing rear wheels on 63’

Yea you can jack up that far forward, motor is plenty of counter balance, or even without a motor . After I installed my monoleafs which were a lot stiffer I still couldn't get these wide tires on with suspension dropped so I made up a deal with what I could find on hand ,all-thread, channel metal s...
by poboyjo65
Thu May 09, 2024 8:19 pm
Forum: 64 - 65 Comets
Topic: Lou's 65 Comet Build
Replies: 957
Views: 183801

Re: Lou's 65 Comet Build

Yea once you think of heat shrink as a universal covering it opens up many uses. Started with the lanyards, but have found a few other uses for it on my build! Lou I'm surprised you didn't cover the whole lanyard,,,or at least up past the part that looks to be rubbing on the hood trim. :? btw, did ...
by poboyjo65
Tue May 07, 2024 7:09 pm
Forum: 64 - 65 Comets
Topic: Lou's 65 Comet Build
Replies: 957
Views: 183801

Re: Lou's 65 Comet Build

I so very much needed to see this.especially that last pic! :D my flange was wavy & not put together right in places with one side of flange higher than the other. I had been trimming it & getting the waves out a while back. Now I know how I will check it all . So Thanks again. been in the back of m...
by poboyjo65
Tue May 07, 2024 1:38 pm
Forum: Comet Lounge
Topic: Zinc info
Replies: 8
Views: 183

Re: Zinc info

Fred basically he said too much of a good thing is not good. Use the proper amount for break in and be done with it.
by poboyjo65
Mon May 06, 2024 6:06 pm
Forum: Comet Lounge
Topic: Zinc info
Replies: 8
Views: 183

Zinc info

If you have 20 spare minutes this is kinda interesting;
https://www.youtube.com/watch?v=erxjPicpYyw
by poboyjo65
Mon May 06, 2024 12:04 pm
Forum: 64 - 65 Comets
Topic: Seat Track Nightmare
Replies: 4
Views: 230

Re: Seat Track Nightmare

fuzzydriver after looking at the picture/exploded view of seat & parts that you found & posted from Kevins post again I noticed at the top of the page is an enlargement of the attachment of the wire to front of the seat .instead of hogrings it looks like hooks,,,,which make more sense > would be eas...
by poboyjo65
Sat May 04, 2024 4:40 pm
Forum: 64 - 65 Comets
Topic: Seat Track Nightmare
Replies: 4
Views: 230

Re: Seat Track Nightmare

Here are some pics of the seat out of my car with wire that is run thru 2 or 3 rings on the frame. if you zoom in on second pic you can see that it would be above the hog rings that are holding the cover on which helps it get over the hump https://i.postimg.cc/DZQ9BKP9/SDC11133.jpg https://i.postimg...
by poboyjo65
Sat May 04, 2024 2:36 pm
Forum: 64 - 65 Comets
Topic: Seat Track Nightmare
Replies: 4
Views: 230

Re: Seat Track Nightmare

If what you are calling a tie rod is the wire that goes from one side track lock to the other side one with a turn buckle to adjust it. It should be ran through a hog ring at front of seat in the center of the seat. This takes up the slack while keeping it from dragging on the drive shaft tunnel. I ...
by poboyjo65
Sat May 04, 2024 2:24 am
Forum: 64 - 65 Comets
Topic: Root's 64 Cyclone Build
Replies: 280
Views: 10923

Re: Root's 64 Cyclone Build

That's impressive! :D
by poboyjo65
Fri May 03, 2024 9:25 pm
Forum: Showing Off
Topic: Let me start!!!!!!!!
Replies: 664
Views: 233807

Re: Let me start!!!!!!!!

Looks great Fred! :D with same od It may not be lower but the taller rim is closer to fender at top giving the eye a lower perspective .
by poboyjo65
Wed May 01, 2024 11:49 am
Forum: Comet Lounge
Topic: WOW the birthdays!!!!
Replies: 627
Views: 124999

Re: WOW the birthdays!!!!

Happy Birthday Boss ! :D
by poboyjo65
Mon Apr 29, 2024 6:36 pm
Forum: 60 - 63 Comets
Topic: 63 single master bowl upgrade to dual
Replies: 7
Views: 274

Re: 63 single master bowl upgrade to dual

Going to a dual master is OK, but if you don't replace all the wheel cylinders as well. why bother with the master. I would say for the safety of the dual MC. because if you rupture a line with a single MC you wont have any brakes at all. but if you rupture a line with a dual MC it can only affect ...